富美家冰火板為雙面復合厚度為0.7-1.2mm防火皮，中間芯材為無石棉纖維水泥板或是硅酸鈣板的防火裝飾材料。工程施工完畢后有某些板材表層有損壞現象。

Fumeijia ice fire board is a double-sided fire-proof sheet with a composite thickness of 0.7-1.2mm, and the middle core material is a fire-proof decorative material of asbestos free fiber cement board or calcium silicate board. After the construction of the project, some of the surface plates were damaged.

輕微損壞狀況：就是指板材表層有微小的裂紋，遠距離看不出來裂紋，只有近距才可以見到。發生這種難題的緣故有多種，有可能是分板過程中損壞了表皮，有可能因?yàn)槭芡獠繙囟葷穸茸儎?dòng)，表皮和芯材變形系數不一樣所致。輕微難題用涂料或漆修補即可。

Slight damage condition: it means that there are tiny cracks on the surface of the plate, which can not be seen from a long distance, but can only be seen from a short distance. There are many reasons for this problem. It may be that the skin was damaged during the splitting process, or the skin and core material have different deformation coefficients due to the change of external temperature and humidity. Minor problems can be repaired with paint or paint.

木紋色可調接近的若干漆，依照板材紋理修補。如果發生小范圍掉皮狀況，可用膩?zhàn)踊蚴窃踊覂?nèi)搭，將木板處理平整，再補同色調的漆或涂料。

Several paints with adjustable wood grain color can be repaired according to the board texture. If peeling occurs in a small area, putty or putty can be used to build the board, and the board shall be treated flat, and then the paint or coating of the same color shall be added.

破損嚴重的木板只有拆換板材。由于工程施工完畢，拆換板材有相應技巧，防止破壞周圍板材。

The only way to replace seriously damaged boards is to replace them. As the construction of the project is completed, there are corresponding skills to remove and replace the plates to prevent damage to the surrounding plates.

板材表層破損比較嚴重，表皮修補難度比較大，只有換板。此安裝工序?yàn)槟z粘，有封邊條固定。下面是換板過程。

The surface layer of the board is seriously damaged, and the skin repair is difficult. Only the board is replaced. This installation procedure is adhesive and fixed with edge banding. The following is the board replacement process.

用角磨機或是手提鋸拆換無齒鋸片，將墻面壞板切割出裂口，用錘子和鑿子工具拆除壞板。

Use an angle grinder or a portable saw to remove and replace the toothless saw blade, cut a crack in the broken wall plate, and use a hammer and chisel to remove the broken plate.

板材拆除完畢，找出板材破損緣故，是因?yàn)橐r板阻燃膠合板變形，導致冰火板表皮破裂。將阻燃膠合板變形嚴重部分切割修補，做成平面。

After the removal of the board, find out the reason for the damage of the board. The reason is that the flame retardant plywood of the lining board is deformed, resulting in the crack of the ice fire board skin. Cut and repair the severely deformed part of fire-retardant plywood to make it flat.

接下來就是換新板，有電源開關位置開孔，提前量好距離，用角磨機或是手提鋸開孔。開孔完畢。裝飾線條，輔料結構膠，雙面膠等準備齊全，開始掛板。

The next step is to replace the board with a new one. The hole is opened at the power switch position. The distance is measured in advance and the hole is opened with an angle grinder or a hand-held saw. Opening is completed. Decorative lines, auxiliary materials, structural adhesive, double-sided adhesive, etc. are fully prepared, and hanging boards are started.

雙面膠起到臨時固定作用。結構膠為主要固定。如果北方或是氣候干燥的地區掛板，膠點要密集，推薦10-15cm膠點間距。固定方式是結構膠和免釘膠結合使用，保證板材不會因?yàn)榭照{(diào)暖氣等緣故變形翹曲。更多相關內容的了解就來我們網站http://0473114.cn咨詢吧！

The double-sided adhesive tape serves as temporary fixation. Structural glue is the main fixation. If the hanging board is in the north or in the dry climate area, the glue points should be dense, and the glue point spacing of 10-15cm is recommended. The fixing method is the combination of structural glue and nail free glue to ensure that the board will not be deformed or warped due to air conditioning, heating, etc. For more information, please come to our website http://0473114.cn Consult!