好看的课外书,盗墓笔记小说txt下载

如何解決防火板加工時出現的爆邊問題？

來源：http://0473114.cn/ 日期：2021-05-07 發布人：admin

如何解決防火板加工時出現的爆邊問題？

How to solve the problem of edge burst in the processing of fireproof board?

(一)、出現上面爆邊

（1） The top edge appears

1、主鋸片太鈍，鋸齒太少

1. The main saw blade is too blunt and the saw teeth are too few

2、主鋸片高出板材太少

2. The main saw blade is too little higher than the plate

3、板材質量太差，會很快鈍鋸片

3. If the quality of the plate is too poor, the saw blade will be blunt soon

4、重新更換鋸片

4. Replace the saw blade again

5、升高主鋸片

5. Raise the main saw blade

6、選用雜質少、質量高的板材

6. Select the plate with less impurities and high quality

(二)、出現下面爆邊(鋸后的板材)

（2） There is edge burst below (sawn board)

1、副鋸片太鈍

1. The saw blade is too blunt

2、副鋸寬度不夠、太窄

2. The width of the auxiliary saw is not enough or too narrow

3、主、副鋸片中間線不重合

3. The middle line of the main saw blade and the auxiliary saw blade does not coincide

4、重新更換鋸片

4. Replace the saw blade again

5、換鋸片或增加鋸片厚度

5. Change saw blade or increase saw blade thickness

6、重新調整副鋸左右位置

6. Readjust the left and right position of the auxiliary saw
富美家山東總代理

(三)、有燒焦的痕跡(鋸后板材上)

（3） There are burning marks (on the sawn plate)

1、合金鋸片太鈍，鋸片上鋸齒太多

1. The alloy saw blade is too blunt and there are too many teeth on the saw blade

2、轉速過高或進料太慢

2. Too high speed or too slow feeding

3、更換鋸片，選擇適當?shù)匿徠?/div>

3. Replace the saw blade and select the appropriate one

4、選擇適當?shù)霓D(zhuǎn)速和進料速度

4. Select the appropriate speed and feeding speed

(四)、在鋸切時有工件被副鋸頂起來的現象

（4） During sawing, the workpiece is jacked up by the auxiliary saw

1、副鋸片太鈍

1. The saw blade is too blunt

2、副鋸片升得太高

2. The auxiliary saw blade rises too high

3、更換鋸片

3. Replace the saw blade

4、適當降低副鋸片高度

4. Reduce the height of the auxiliary saw blade appropriately

(五)、中間貼面板爆邊

（5） Edge burst of middle panel

1、板材較厚，每塊微彎不平整，上下面互疊一起后產生縫隙

1. The plate is thick, each piece is slightly bent and uneven, and the upper and lower parts are overlapped to form a gap

2、機械壓料的氣缸壓力不夠

2. The cylinder pressure of mechanical pressing is not enough

3、工件板面有條紋(凹凸)也會爆邊

3. The work piece plate surface has the stripe (concave convex) also can burst the edge

4、工作鋸切時少壓2-3塊板材

4. Press 2-3 pieces less when sawing

5、鋸切板材時進刀速度適當調慢適切認可

5. When sawing the plate, the feed speed should be adjusted to be appropriate

6、檢查鋸片是否不鋒利，及時修磨刃口

6. Check whether the saw blade is not sharp, and repair the edge in time

感謝您的閱讀，希望以上內容對您有所幫助，如您想了解更多精彩內容請點擊我們的官網：富美家山東總代理http://0473114.cn。

Thank you for your reading. I hope the above content will be helpful to you. If you want to know more wonderful content, please click our official website: fumika Shandong general agent http://0473114.cn .

上一篇：UV快裝板在家居裝飾方面的應用！ 下一篇：輕質復合墻板質量驗收標準是什么？

分類導航

產品中心

聯系我們

成功案例

聯系我們

新聞動態

聯系我們

熱門產品推薦

相關新聞